|
Latest Issue
 |
- Category: Articles
Problems Faced in Service Life Estimation of Blade Bearings
The blade bearings of wind turbines allow the required oscillation to control the loads and power of the wind turbine. The pitch system brings the blade to the desired position by adapting the aerodynamic angle of attack. The pitch bearing, which is connected to the blade and the hub of the turbine, is subjected to high axial forces and bending moments. The conditions of these bearings are unique and most standards to estimate bearing service life are designed for rotating bearings and do not consider the oscillation. This article gives a brief overview of the current problems of blade bearings. The article focuses on the tribological challenges like fatigue life calculation of oscillating bearings, different wear damage modes like false brinelling and fretting wear, grease lubrication and the contact conditions occurring under different operating environments.
By Fabian Schwack and Prof. Dr.-Ing. Gerhard Poll, Institute of Machine Design and Tribology, Germany
- Category: Articles
Spinner Anemometer Provides Transparency in the Performance of All Turbines in a Wind Farm
Wind turbines are energy producing devices. Hence it is important for the customer and the manufacturer to know if a turbine efficiently converts the kinetic energy from the given wind conditions into power. This power performance characteristic is commonly expressed as electrical power (output) versus horizontal wind speed (input) measured under free inflow conditions at a distance of two to four rotor diameters in front of the turbine. Here is where the big dilemma in the wind industry lies.
 |
 |
On the one hand every turbine should be monitored to make sure its performance characteristic is within the specification, but on the other hand it is almost impossible to measure the wind quantities at all turbines and at all sites, using met masts or other non-standard forward-looking measurement systems.
By Harald Hohlen, ROMO Wind
- Category: Articles
Security and Protection Using Sensor Systems
Sensor systems for offshore wind farms are used for the monitoring of many environmental and operational parameters. They monitor the internal turbine and loads condition, and also the environment of offshore wind farms. Wind speeds, wave heights and swell, as well as parameters related to the turbine condition such as oil temperature or pressure or rotor speed, are measured by sensor systems. However, sensors are also vital for safety and security. Each offshore wind farm element must be equipped with a fire detection system, which is based on sensor information. Access restrictions to sensitive areas (e.g. the monitoring room or nacelle) are also managed by sensors, and sensor systems guarantee the safe condition and positioning of rotor and nacelle (yaw system). The research project OWiSS, which is described below, focuses in particular on the safety and security issues.
By Julia Klatt, Deutsche Offshore Consult, Germany
- Category: Articles
Developments in Mooring Installation Technology for Floating Offshore Wind Structures
As floating wind turbines move into deeper waters, the capital expenditure (CAPEX) costs for mooring and installation will contribute a significant proportion of the overall project budget. Offshore wind developers are looking for a new mooring methodology to reduce costs, minimise installation times and reduce health and safety risks. The mooring of offshore wind platforms has been identified as the critical success factor in the future of floating offshore wind. High installation costs and the cost of anchoring are delaying and restricting the commercialisation of the sector.
By Greg Campbell-Smith, Global Business Development Manager, First Subsea, UK
- Category: Articles
Faster Failure Detection in Wind Turbine Drive-Trains
Machine learning is finding its way into wind energy. It can be beneficial in many aspects of the wind industry value chain, ranging from the planning phase of new farms to operational optimisation during their service life. For the latter it has big potential. A turbine has many sensors that allow detailed monitoring of its operation and this operational data can be used as input for machine learning strategies. By tailoring maintenance strategies to the information coming from anomaly detection based on monitoring algorithms maintenance can be optimised and turbine uptime improved. In particular by using already available SCADA sensor data, optimisation potential can be realised rapidly.
By Prof. Jan Helsen and Ing. Pieter Jan Jordaens, OWI-lab, Belgium
- Category: Articles
Europe’s Wind Productivity to Rise 30%
Researchers from Imperial College London and ETH Zürich have developed a new multi-decade simulation of wind power production in Europe. Using global weather data from NASA, they estimated the hourly output from tens of thousands of wind farms that are currently operating or in the planning pipeline. With this, they found that technical improvements over the last ten years have led to significant increases in average capacity factors – and that the continued move towards larger machines placed further offshore will see this continue into the future. They predict that Britain’s capacity factor will rise from 32 to 39%, and Germany’s from 19 to 29% because of large developments in the North Sea, whereas capacity factors in Spain and Italy will see more modest growth due to limited new investment. Their research has led to the development of a new open-access tool that can simulate wind and solar power anywhere in the world, which is available at www.renewables.ninja.
By Iain Staffell, Imperial College London, UK, and Stefan Pfenninger, ETH Zürich, Switzerland
- Category: Articles
Making Life Easier and Safer for Technicians
Technical innovations are constantly influencing the way blade repair is conducted within the wind sector, as project owners seek to shorten inspection and maintenance times, make the most of short service windows and increase the longevity of their assets by incorporating the latest technology into their strategies. In this article Tom Dyffort, Managing Director of blade repair and inspection specialist Altitec, discusses the five technological advancements that have most influenced the sector over the last decade.
By Tom Dyffort, Managing Director, Altitec, UK
